Skip to content

Inkbird ITC-308 WiFi Temperature Controller

WiFi thermostat with two outlets for heating and cooling. Turns a fridge into a fermentation or curing chamber, with app and alarms.

559,-

Gives 56 bonus points to members upon purchase
In stock
Placeholder for rich text
Placeholder for rich text
Få beskjed når varen er på lager
Item No.: 2562
Sikker betaling
1-5 dagers levering
Angrerett / Garanti
Hvorfor logge inn?
🎁 10% rabatt på dette kjøpet
💰 Bonuspoeng på alt du handler
🚚 Gratis frakt over 1000kr (inntil 15kg)

This product is temporarily out of stock. If you would like to receive an email when it’s back, enter your email address in the form below.

Information

Inkbird ITC-308 WiFi: Turn a Fridge into a Curing or Fermentation Chamber

Steady temperature is half the craft, whether you are curing ham, fermenting beer or pickling vegetables. The Inkbird ITC-308 WiFi is a ready-wired thermostat with two power outlets: the fridge in one, a heat source in the other, and the probe inside the chamber. The controller switches heating and cooling on and off automatically around your chosen temperature, and with WiFi and the INKBIRD app you monitor everything and get alarms straight to your phone.

Two outlets: heating and cooling
WiFi and app with alarms
Plug and play with EU plug
Compressor protection for fridges

This is the classic way to build a curing chamber or fermentation chamber from an ordinary fridge, with no modification of the fridge itself. The built-in compressor delay protects the fridge from rapid start-stop cycles, the dual display shows measured and set temperature at the same time, and the alarms warn you of too high or too low temperature and sensor faults. The controller handles loads up to 2200 W, more than enough for fridges, heating cables, heat mats and small heaters.

Pro tip!
When building a curing chamber from a fridge, place the probe in the middle of the chamber at the height of the meat, not against the wall. Set the temperature to 10-15 degrees and put a small heat source in the second outlet, and the chamber holds a steady temperature even in a cold cellar in winter.

Features

  • Dual relay control: Separate outlets for heating and cooling, the controller switches between them automatically.
  • App monitoring: Follow the temperature and get alarms on your phone via the free INKBIRD app (WiFi, 2.4 GHz).
  • Safe for the fridge: Adjustable compressor delay prevents rapid start-stop cycles.
  • Precise control: Range -40 to 100 degrees C, accuracy ±1 degree, with calibration and selectable °C/°F.
  • Waterproof probe: NTC sensor with IP68 sealing and approx. 1.8 m cable, handles humid chambers and liquid baths.
  • Ready to use: Plug and play with EU plug, no wiring or installation needed.

How to use

  1. Plug the fridge into the cooling outlet and any heat source into the heating outlet.
  2. Place the probe where the temperature should be measured, in the middle of the chamber or in the liquid.
  3. Set the target temperature and difference on the controller or in the app.
  4. Connect to WiFi via the INKBIRD app for monitoring and alarms on your phone.

Specifications

Product Temperature controller with WiFi, heating and cooling outlets
Brand Inkbird
Model ITC-308 WiFi (EU plug)
Temperature range -40 to 100 °C
Accuracy ±1 °C, resolution 0.1 °C
Max load 10 A, 2200 W at 220-240 V
Probe NTC sensor, IP68 waterproof, approx. 1.8 m cable
WiFi and app 2.4 GHz, free INKBIRD app (iOS 11+ / Android 5+)
Safety Compressor delay, high/low alarms, sensor fault warning
In the box ITC-308 WiFi controller with probe and manual

FAQ Frequently asked questions

Can I build a curing chamber from an ordinary fridge with this?

Yes, that is one of the most common uses. Plug the fridge into the cooling outlet, hang the probe in the middle of the chamber and set 10-15 degrees, and the controller keeps the temperature stable. The compressor delay protects the fridge, and in cold surroundings you can add a small heat source in the heating outlet.

How do the two outlets work?

One outlet is for cooling and the other for heating. If the temperature falls below the set value minus the difference, the heating outlet switches on; if it rises above, the cooling outlet switches on. You can use both at once or just one, the controller manages them independently.

Do I need WiFi for it to work?

No, the controller works perfectly well on its own with the display and buttons on the unit. WiFi and the INKBIRD app are an addition that lets you follow the temperature and receive alarms on your phone, handy when the curing chamber is in the basement. Note that it connects to 2.4 GHz networks.

How much load can the controller handle?

Up to 10 A, which corresponds to around 2200 W on European mains. That is plenty for fridges, freezers, heating cables, heat mats and small heaters. For larger loads than this, use the controller together with an external relay.

Manufacturer

Foodstuff Collection

Reviews

Relaterte produkter

Alternative produkter

  • visa.png
  • mastercard-full.png
  • vipps-orange.png
  • bring.png
  • klarna-dark.png
  • postnord.png
  • posten.png